Changing the oil of Mazdaspeed 3 regularly is very important. But you may face difficulty picking the high-quality oil for your Mazdaspeed 3 and change the oil.
Don’t worry. Here we will show you how you can choose the top quality oil and easily complete Mazdaspeed3 oil change in 5 easy steps.
By the end of this article, you will not only get to know about Mazdaspeed 3 oil changing process, but you will also know the damages old oil causes as well.
Let’s get started.
3 Reasons Why You Change Oil in Your Mazdaspeed 3
You should change the oil of your Mazdaspeed 3 for every 10,000 miles (16,000 KM). Or, in case you don’t drive your Mazdaspeed 3 that much, you need to change the engine oil every 12 months.
Not changing your Mazdaspeed 3 engine oil regularly can lead to severe engine damages. This is why you have to be aware of how you can change the oil.
If you know the 5 steps to Mazdaspeed 3 oil change we discussed in this article, you can save your car from the following damages:
1. Wear Of Components:
An engine consists of many different moving parts, such as valves and pistons. Engine oil lubricates these components and helps them to function correctly. However, old oil can fail to provide enough lubrication.
Insufficient lubrication will undoubtedly damage the components, preventing them from functioning smoothly. This will gradually cause the parts to decay.
2. Engine Overheating:
Engine oil gets thicker with time. There are many factors, such as dirt causes this effect. Thick oil doesn’t work efficiently. It can’t absorb heat, nor can it provide proper lubrication for smooth movement.
As a result, the friction between parts becomes rough, and this generates heat.
This is how old oil leads to overheating of the engine. And just so you know, overheating engines can lead to gasket blow-up.
3. Increase Fuel Consumption:
As you already know, old fuel gets thicker. It means the engine has to work harder to function properly. This can be a reason why your engine will need more fuel to function correctly.
Excessive fuel consumption means you will have to spend more. So as you can see, old engine oil can cause damage to your vehicle, can cause you extra bucks, and it can even cause a blow-up.
To save yourself from all these troubles, follow the method of oil change discussed below. But before going into that, let’s see how you can choose the best quality oil for Mazdaspeed 3.
How To Choose The Best Oil For Mazdaspeed 3
Choosing top-quality oil for your car is very important. It can improve your vehicle’s performance by a lot and keep the engine healthy at the same time.
However, it can be tricky to sort out the best oil for your Mazdaspeed 3. This is why, before jumping into the process of an oil change, make sure you have chosen the right oil.
Here’s what to consider while choosing the best oil for Mazdaspeed 3.
1. Type Of Oil:
Different types of vehicles use different types of oil.
Some use diesel while others rely on gas. But Mazdaspeed doesn’t use either of them. You are required to use synthetic lubricant for a Mazdaspeed 3.
2. Viscosity Of Oil:
It’s important to make sure you are keeping the viscosity of oil in mind every time you refill.
The oil viscosity is usually expressed in codes. For example, a Mazdaspeed’s oil viscosity is 5w-30. Here 5 is the col viscosity and 20 is the hot viscosity at the engine’s maximum running temperature.
You will find your car’s accurate viscosity in its manual.
3. Grade Of Oil:
Oil grade depends upon the type of oil you need to use. The two most common oil grades are SN and SP. However, just the type of oil, Mazdaspeed uses neither of these grades.
Instead, Mazdaspeed uses SM oil. So make sure to check the oil grade before using.
If you follow these steps, you are sure to get your hands on the top-quality oil for your Mazdaspeed 3.
5 Easy Steps For Mazdaspeed3 Oil Change
You have to take care of your Mazaspeed3 oil change today or tomorrow. The issues we discussed just now should be enough to show you why you need to change the oil.
However, the main process of Mazdaspeed 3 oil change doesn’t have to be as difficult as it sounds.
Here we have discussed 5 simple steps to perform Mazdaspeed 3 oil change perfectly without any unnecessary hassle.
But before getting into the main process, make sure you have the following tools within your reach,
- Oil Filter Wrench
- Ratchet Set
- Rhino Ramps
- Oil Drain Pan
- 6mm Hex Allen Key
- 4.5 Quarts of 5W-20 Oil
- Oil Filter
- Small Flathead Screwdriver
After you have collected all these essentials, follow the process step by step.
Step 1: Lift The Front End Of Your Mazdaspeed 3
You have to make sure that your car is perfectly positioned. You have to lift the front part of the car off the ground.
You need to do this so that you can easily access the oil filter and the oil pan. Using ramps to lift the car can be a smart move. It is easy and requires less effort.
Step 2: Drain All The Oil From The Oil Pan
Now, as everything is in perfect position, you need to drain the old oil out of the oil pan.
To do that, you have to,
- Move the drain pan under the pan located near the rear of the engine.
- Remove the oil plug using a wrench or a 17mm socket
- Wait for all the oil to drain
- Re-install the oil pan drain plug
Step 3: Remove The Plastic Belly Pan
Now it’s time to start the process of re-filling with new oil. You will have to start the process by removing the plastic belly pan of your Mazdaspeed 3 first.
Use a wrench to remove 7 of the 10mm hex bolts and 2 plastic fasteners holding the plastic belly. After removing them, put the belly pan aside.
Now you have full access to everything.
Step 4: Locating The Oil Filter
After removing the plastic belly pan, look for the oil filter. It should be right there.
Once you have found the oil filter, remove the cap. Use a stamped oil filter wrench to do so. This will drain all the oil clogged in the filter.
Once all the oil is out, put the cap back on.
Step 5: Refill With New Oil
Now it’s time to refill with the new oil. This will complete the oil changing process. Unscrew the oil fill cap first. You will find the oil fill cap on the top part of the engine. It is the only hole located there.
Turning the cap anti-clockwise should unscrew it properly. Then place a funnel after removing the cap.
Now pour in 4 quarts of oil. Usually, Mazdaspeed 3 oil capacity is 4.25 quarts, but you have to leave a bit of room. Put the cap back on after all the oil is poured.
And now you are done. This is how you can perfectly change the oil of your Mazdaspeed 3 in the simplest way possible.
How many quarts of oil does a Mazdaspeed 3 take?
Here are different Mazdaspeed 3 models oil capacity,
- 2007 Mazdaspeed 3 Oil Capacity is 3.9 – 4.3 quarts
- 2008 Mazdaspeed 3 Oil Capacity is 4.5 – 5.0 quarts
- 2010 Mazdaspeed 3 Oil Capacity is 4.2 – 4.5 quarts
What kind of oil does a Mazdaspeed 3 take?
The top quality oil type for Mazdaspeed 3 is 5W20.
When should I change my oil Mazdaspeed 3?
You should change your Mazdaspeed 3 oil at least once every 12 months or after every 10,000 miles (16,000 Km).
How much oil does a 2011 Mazdaspeed 3 take?
A 2011 Mazdaspeed 3 can take up to 6 U.S. quarts.
What is 0W-20 synthetic oil?
Yes, 0W-20 is full synthetic motor oil.
What type of oil does a 2011 Mazdaspeed 3 use?
A 2011 Mazdaspeed 3 uses 0W-20.
Mazdaspeed 3 oil change regularly is an essential task when you want to maintain your Mazdaspeed 3 perfectly and keep its engine safe and healthy. From today’s article, you can see that the oil change process is not hard.
In fact, this is the easiest method you can find online. So, pick fully synthetic oil and change it regularly and thus keep your car perfect always.
However, if you have any confusion left, do not hesitate to comment below.